Remove any oil from the surface with an alcohol swab.
Clean the work area of dust before applying. Unused or extra films can clean dust effectively before applying.
Tap water may cause clouding.
Applying films under a bright light is recommended for accuracy.
When removing a film using a tweezers, watch your pressure as it can leave a mark on the film.
First applying films to parts that are prone to scratches, such as case back can make the process easier.
When applying to the case back, bezel and glass, it is better to apply from outside to inside. For example, if glass film is applied first, then it can come out of place and/or air bubbles can form inside it in the process of applying the bezel film.
When removing doughnut-shaped films such as bezel or case back films, it is easier to remove the films within them first.
If stretching is needed, do not stretch films before applying. Apply and then stretch. Beware that, once stretched, the film is difficult to restore to the original form.
Due to the curved nature of crown guards, films for these parts are prone to peeling.
01
Please clean your watch so that there is no dirt or dust.
Fill the enclosed spray bottle with pure water.
02.1
Using the enclosed plastic tweezers, carefully peel off the shell.
02.2
Spray water on the sticky side of the shell and place the shell on the corresponding part of your watch.
03
Remove as many water bubbles inside the shell as you can.
You can gently push out the water bubbles with the plastic tweezers or with your fingers.
04
We recommend that you dry the shell for at least 3 minutes after every attachment of a piece of shell.
05
After 3 at least minutes, press the attached area firmly so that the shell becomes secured.
06
Finally, this is the most important step. PLEASE DO NOT WEAR YOUR WATCH FOR AT LEAST ONE DAY. It takes time to become fully secured.
Congratulations!
07
Now you are the owner of a WATCHSHELLED timepiece.
You can keep your timepiece in a new condition as long as you use WatchShells.
Some water bubbles may remain after the shell dries. Most of the remaining water bubbles will be removed during the drying process.
Coverage
✓ CASE - Front / Back / Side (3 o'clock / 9 o'clock)
✓ LUG - Front / Back
✓ GLASS (excl. Cyclops)
✓ BEZEL INSERT
✓ BRACELET (including Link & Screw)
✓ BUCKLE - Front / Side
We do not create shells for Jubilee bracelets.
We do not create shells for Fluted bezels.
For Daytona, there is a slight difference in the lugs. Therefore, when you install the shells, please take care to refer to the directions we noted in the YouTube film.
HOW TO
Please refer to our YouTube Tutorial before installing.
Tips from customers
Remove any oil from the surface with an alcohol swab.
Clean the work area of dust before applying. Unused or extra films can clean dust effectively before applying.
Tap water may cause clouding.
Applying films under a bright light is recommended for accuracy.
When removing a film using a tweezers, watch your pressure as it can leave a mark on the film.
First applying films to parts that are prone to scratches, such as case back can make the process easier.
When applying to the case back, bezel and glass, it is better to apply from outside to inside. For example, if glass film is applied first, then it can come out of place and/or air bubbles can form inside it in the process of applying the bezel film.
When removing doughnut-shaped films such as bezel or case back films, it is easier to remove the films within them first.
If stretching is needed, do not stretch films before applying. Apply and then stretch. Beware that, once stretched, the film is difficult to restore to the original form.
Due to the curved nature of crown guards, films for these parts are prone to peeling.
01
Please wipe the surface of the watch clean so that there is no dirt or dust. Please put pure-water in the enclosed spray.
02.1
Using the enclosed plastic tweezers,
carefully peel off the shell.
02.2
Spray water on the sticky side of the shell and place the shell on the corresponding part of your watch.
03
Remove as many water bubbles inside the shell as you can.
You can gently push out the water bubbles with the plastic tweezers or with your fingers.
04
We recommend that you dry the film for at least 3 minutes after every attachment of a piece of shell.
05
After 3 at least minutes, press the attached area firmly so that the shell becomes secured.
06
Finally, this is the most important step.
PLEASE DO NOT WEAR YOUR WATCH FOR AT LEAST ONE DAY.
It takes time to become fully secured.
Congratulations!
07
Now you are the owner of a WATCHSHELLED timepiece.
You can keep your timepiece in a new condition as long as you use WatchShells.
Some water bubbles may remain after the shell dries. Most of the remaining water bubbles will be removed during the drying process.
Coverage
✓ CASE - Front / Back /
✓ Side (3'o clock / 9 o'clock)
✓ LUG - Front / Back
✓ GLASS (excl. Cyclops)
✓ BEZEL INSERT
✓ BRACELET
✓ (including Link & Screw)
✓ BUCKLE - Front / Side
We do not create shells for Jubilee bracelets.
We do not create shells for Fluted bezels.
For Daytona, there is a slight difference in the lugs. Therefore, when you install the shells, please take care to refer to the directions we noted in the YouTube film.
by HARTIST&COMPANY
by HARTIST&COMPANY
